Designs (816)

816 Results - Page 1/82 |< < 1 2 3 4 5 > >|

TPS54350EVM-235: 3.3V @ 3A, 6 ~ 18 Vin

Manufacturer: Texas Instruments

The TPS54350 dc/dc converter is designed to provide up to 3-A output from a nominal 12-V (6-V to 18-V) input voltage source. Rated input voltage and output current range is given in Table 1−1. This evaluation module is designed to demonstrate the small PCB areas that may be achieved when designing with the TPS54350 regulator and does not reflect the high efficiencies that may be achieved when des…

View Design

UCC28600EVM: 120W, 19.4V @ 6.2A with PFC, 85~265VAC

Manufacturer: Texas Instruments

The UCC28600 evaluation module (EVM) is a 120-W off-line quasi-resonant flyback converter providing a 19.4-V regulated output at 6.2 A of load current, operating from a universal ac input.

View Design

STEVAL-ISA018V1: 150W, 24V @ 6A, 85~185/185~265VAC

Manufacturer: STMicroelectronics

This user manual describes a high efficiency solution for industrial power supplies with a continuous output power of 150 W and peak power up to 240 W. It takes advantage of the resonant approach to minimize switching losses, resulting in higher than 90% efficiency. The topology is based on half-bridge and operated in a resonant fashion by means of a resonant LC tank, driven by the L6599 dedicate…

View Design

LM5008EVAL: 10V @ 300mA, 12 ~ 95V in

Manufacturer: Texas Instruments

The LM5008 Step down switching regulator features all of the functions needed to implement low cost, efficient, Buck bias regulators. This high voltage regulator contains a 100V, 0.5A N-channel Buck switch.

View Design

AN954: Off-Line Capacitive Power Supply

Manufacturer: Microchip Technology

* From page 10 of AN954: Figure 10 shows a capacitive power supply with several UL considerations designed in. A fuse is added to protect the circuit during an over-current condition. Adding R2 in parallel with C1 creates a filter that will attenuate EMI from traveling back onto the line. A varistor, or MOV, provides transient protection.

View Design

STEVAL-ISA019V2: 80W, 24V @ 3.3A, 160 ~ 550VAC

Manufacturer: STMicroelectronics

The purpose of this application note is to explain the design of an 80 W 3-phase auxiliary power supply for motor drives and welding applications. To reach a high level system in terms of both efficiency and cost, the L6565 PWM controller has been selected as well as the STC04IE170HV as the main switch. The combination of these STMicroelectronics parts provides a highly efficient solution for hig…

View Design

EVAL5986A: 1.8V @ 2.5A, 2.9 ~ 18 Vin

Manufacturer: STMicroelectronics

The L5986 is a step-down switching regulator with 3.0 A (minimum) current limited embedded power MOSFET, so it is able to deliver up to 2.5 A current to the load depending on the application conditions.

View Design

STEVAL-ISA009V1: 24W, 12V @ 2A, 90 ~ 264VAC

Manufacturer: STMicroelectronics

The VIPer53 combines an enhanced current mode PWM controller with a high voltage MDMesh Power Mosfet in the same package. VIPer53 is available in two different packages, DIP-8 and PowerSO-10. This reference board is an offline wide range power supply that incorporates VIPer53 and is set up for secondary regulation by driving the PWM controller through an optocoupler.

View Design

EVALVIPER17L-7W: 12V @ 600mA, 90 ~ 265 VAC

Manufacturer: STMicroelectronics

The new VIPer17 device integrates in the same package two components: an advanced PWM controller built in BCD6 technology and an 800 V avalanche rugged vertical power MOSFET. The device is suitable for off line power converter operating both, with wide range input voltage (85 VAC - 270 VAC) up to 7 W or with single range input voltage (85 VAC - 132 VAC or 175 VAC – 265 VAC). With European range i…

View Design

XRP7714EVB-DEMO-2P-KIT: 4 Chan, 4A, 4.5 ~ 25V in

Manufacturer: MaxLinear, Inc.

The XRP7714EVB-DEMO-1, XRP7714EVB-DEMO-2, and the XRP7714EVB-DEMO-2P demo boards are complete, working, four channel, power systems measuring either 2”x2”, or 2”x2.5” capable of delivering over 35 watts. They provide 3.3V, 2.5V, 1.8V, and 1V at a maximum of 4 amps per channel. The 2.5V, 1.8V, and 1V supplies can be adjusted in 50mV increments, and the 3.3V supply is adjustable in 100mV increments.…

View Design
816 Results - Page 1/82 |< < 1 2 3 4 5 > >|