Designs (216)

216 Results - Page 21/22 |< < 18 19 20 21 22 > >|

DC2043A: 4 Lead-Acid Cell Balancer, 12 ~ 64V in

Manufacturer: Linear Technology/Analog Devices

Demonstration circuit 2043A is a lead Acid Battery Balancer featuring the LTC®3305.

View Design

DC1894B: 12-Cell Battery Monitor, 11 ~ 55V in

Manufacturer: Linear Technology/Analog Devices

Demonstration circuit 1894B is a daisy-chainable isoSPI battery-stack monitor featuring the LTC®6804-1.

View Design

TSDMTX-5V2-EVM: Dual-Mode (Qi and PMA) Wireless Charging Transmitter with QC2.0/3.0 Option

Manufacturer: Semtech Corporation

The Semtech TSDMTX-5V2-EVM is an evaluation platform for test and experimentation of a wireless charging transmitter based on the Semtech TS80000 Wireless Power Transmitter Controller, TS61001 Full-Bridge FET Driver, and TS31023 Linear Regulator. This evaluation module provides a complete system solution for both Qi and PMA standards of power transmission.

View Design

760308MP: 15W Medium Power Qi Charger

Manufacturer: Rohm Semiconductor

The ROHM-760308MP-EVK-001 Wireless Power Evaluation kit is based on the Qi specification 1.2.2 and supports the Extended Power Profile (EPP) from the Wireless Power Consortium (WPC). Receiver and transmitter are also backwards compatible with the low power mode (Baseline Power Profile).

View Design

PMP11114.2: USB Type C, 3A &amp; 1.5A Charger, 7 ~ 18V in

Manufacturer: Texas Instruments

PMP11114 is a dual port USB Type C Charger. This design takes an automotive input voltage (7V to 18V nominal, load dump to 40V). The output goes to two USB Type ports, each of these ports supplies 5V. The design supports 3A on one port and 1.5A on the other port. The DC/DC portion of the design is rated for 5A total current. The design is fully compliant with USB type C and backwards complian…

View Design

NCP380LMUAJAGEVB: 2.1A, 2.5 ~ 5.5V in, High-side

Manufacturer: ON Semiconductor

The NCP380 is a high-side power distribution switch designed for applications where heavy capacitive loads and short-circuits are likely to be encountered

View Design

EPC9055: 3A, 0 ~ 100V, Half H-Bridge Driver

Manufacturer: EPC

This development board is in a monolithic half bridge topology with onboard gate drives, featuring the EPC2106 eGaN

View Design

EPC9019: 20A, 0 ~ 80V, Half H-Bridge

Manufacturer: EPC

These development boards are in a half-bridge topology with onboard gate drives, featuring theEPC2015/23 and EPC2001/21 eGaN® field effect transistors (FETs).

View Design

EPC9089: 4A, 0 ~ 80V, 10MHz, Class E Amplifier

Manufacturer: EPC

The EPC9089 is a high efficiency, differential mode Class-E amplifier development board that can operate up to 10 MHz. The purpose of this development board is to simplify the evaluation process of class-E amplifier technology using eGaN IC's by allowing engineers to easily mount all the critical class-E components on a single board that can be easily connected into an existing system.

View Design

STEVAL-ISC004V1: Stand Alone USB PD Source Port Controller

Manufacturer: STMicroelectronics

The STEVAL-ISC004V1 evaluation board is a ready-to-use USB PD source based on STUSB4710A and ST1S14 ICs. It demonstrates how to convert a fixed voltage DC power input into a USB PD variable voltage output.

View Design
216 Results - Page 21/22 |< < 18 19 20 21 22 > >|