IR15-21C/TR8 Datasheet by Everlight Electronics Co Ltd

DATASHEET E _ ”£333..

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

1206 Package Chip Infrared LED

IR15-21C/TR8

Features

․Small double-end package

․High reliability

․Low forward voltage

․Good spectral matching

to Si photodetector

․Pb free

․The product itself will remain within RoHS compliant version.

Descriptions

IR15-21C/TR8 is an infrared emitting diode in miniature

top view flat SMD package and it is molded in a water

clear plastic. The device is spectrally matched with silicon

photodiode and phototransistor.

Applications

․PCB mounted infrared sensor

․Infrared emitting for miniature light barrier

․Floppy disk drive

․Optoelectronic switch

․Smoke detector

Device Selection Guide

Part Category Chip

Material Lens Color

IR GaAlAs Water Clear

Data Sheet 1206 Pm «- Chip Infrared LED ._,..._ Bulk”! MW m" 2.010.? G Anode ¢ 32 02 @‘i‘K—®©Cuihode — + i ~' i «a 3 i D .‘ For reflon soldering (propose) 3.2 15 LS E _ ”53%

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

Package Dimensions

Notes: 1.All dimensions are in millimeters

2.Tolerances unless dimensions ±0.1mm

Data Sheet 1206 Pm me Chip Infrared LED E _ ”332‘:

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Units

Continuous Forward Current IF65 mA

Reverse Voltage VR5V

Operating Temperature Topr -25~ +85 ℃

Storage Temperature Tstg -40 ~ +85 ℃

Soldering Temperature *1 Tsol 260 ℃

Power Dissipation at(or below)

25℃Free Air Temperature Pd130 mW

Notes: *1: Soldering time≦5 seconds.

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Condition Min. Typ. Max. Units

Radiant Intensity IEIF=20mA 0.2 0.8 -- mW/sr

Peak Wavelength λpIF=20mA -- 940 -- nm

Spectral Bandwidth Δλ IF=20mA -- 45 -- nm

Forward Voltage VFIF=20mA -- 1.2 1.5 V

Reverse Current IRVR=5V -- -- 10 μA

View Angle 2θ1/2 IF=20mA -- 160 -- deg

Data Sheet 1206 Pm age Chip Infrared LED mA) Forward Current ( Relative Radiant Intensity (%) / \ 880 900 920 940 960 980 1000 10201040 Ambient Temperature (“ C) Wavelength A (mn) wool s tp/T:0.01 mA) Forward Current lr ( Forward Voltage (V) TFKﬁ’? Approved

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

0

20

40

60

80

100 IF=20mA

Ta=25° C

0

10

101

102

3

104

1 2 3 4 0.1

IF-Forward Current (mA)

10

10010

110

2 3 104

Ie-Radiant Intensity(mW/sr)

1

10

100

0

-40 -20 40200 60 10080

20

40

60

100

80

120

140

Typical Electro-Optical Characteristics Curves

Fig.1 Forward Current vs. Fig.2 Spectral Distribution

Ambient Temperature

Fig.3 Forward Current Fig.5 Relative Intensity vs.

vs. Forward Voltage Forward Current

D E L a u n ﬂ h 0 €53 Ea; 2:3 E _ ”£52.:

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

-20

0.6

0.9

0.7

0.8

1.0

0.20.4 0 0.2 0.4 0.6

50

70

80

60

40

30

-10 0 2010

Typical Electro-Optical Characteristics Curves

Fig.5 Relative Radiant Intensity vs.

Angular Displacement

Data Sheet 1206 Pm me Chip Infrared LED 1 ~ 5°C / sec. —N 260°C Max , loge. Max I’m-heating I ~ 5°C/sec. 180 ~ 200°C E _ ”£52.:

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection , otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃or less and 60%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

Data Sheet 1206 Package Chip Infrared LED E _ ”£333..

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3

seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more

intervals, and do soldering of each terminal. Be careful because the damage of the product is often

started at the time of the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is

unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed

beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

lip Infrared LED / PP:0‘:\ ‘ \ J/ //~\ \ 5/ / \ \ n 6‘ 7g \ F2} 3‘: \iirﬁﬁ"% 7 is: w‘ ’ “—W\‘ t: \m ‘ 0C, // ‘ // A] P Stiub e lEJtClE Progressive direction 2.0:005 4‘0 m.5+o.1 0.23 3 w W * 4i— _ _LO ‘0 T _ its 0 I I”) 40 1 8+O1 Wm L29 ' 'I-r-TJ‘ @‘Bn—oecmue —- ' — + E _ Apéﬁaﬁd

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

Package Dimensions

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

Carrier Tape Dimensions:(Quantity: 2000 PCS per reel)

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

Data Sheet 1206 Package Chip Infrared LED ® EVERLIG-ﬂ' 0 DP" : F/N : XKXXXKKXXXXXX |I|llll||I|I|||||l|I|ll XXXXXKXXXXXX! m :nx Huaxxx REF :xxx New Taipei City 23860, Taiwan http://www.everlight.cum E _ Apéﬁaﬁd

LifecyclePhase:

Revision : 2

Expired Period: Forever

Release Date:2013-07-05 13:36:07.0

Data Sheet

1206 Package Chip Infrared LED

IR15-21C/TR8

Label Form Specification

CPN: Customer’s Production Number

P/N : Production Number

QTY: Packing Quantity

CAT: Ranks

HUE: Peak Wavelength

REF: Reference

LOT No: Lot Number

Notes

1. Above specification may be changed without notice. EVERLIGHT will reserve authority on

material change for above specification.

2. When using this product, please observe the absolute maximum ratings and the instructions

for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for

any damage resulting from use of the product which does not comply with the absolute

maximum ratings and the instructions included in these specification sheets.

3. These specification sheets include materials protected under copyright of EVERLIGHT

corporation. Please don’t reproduce or cause anyone to reproduce them without

EVERLIGHT’s consent.

EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2685-6688

Office: No. 6-8, Zhonghua Rd., Shulin Dist., Fax: 886-2685-2699，6897

New Taipei City 23860, Taiwan

http://www.everlight.com

IR15-21C/TR8 Datasheet by Everlight Electronics Co Ltd

Products related to this Datasheet